PCD-TP110CS/DR-08 is a high-performance PCI-to-PC Card Drive Unit that supports one independent card socket compliant with the 16/32-bit PC Card standard defined in 1997 PC Card Standard.
Povides a rich feature set that makes it the best choice for bridging between PCI and PC Card in desktop computers.
Compliant with the 16-bit PC Card specification defines in PCMCIA Release 2.1 and JEIDA 4.2 and can supports any combination of 16-bit or 32-bit PC Card in the one socket, powered at 5V or 3.3V as required.
The host system interface of PCD-TP110CS is compliant with the PCI Local Bus specification 2.2.
PCD-TP110CS is register set compatible with Intel 82365SL controller and compatible with ExCA, it enables the PCD-TP110CS to support almost all of the PC Card applications including: SRAM card, Linear Flash card, ATA Flash card, Modem card and Wireless 3G/Modem/LAN card.
◎ PCD-TP110CS provides one front-access PCMCIA / CardBus socket solution for PC.
◎ PCI Local Bus Specification Revision 2.2 compliant.
◎ PCMCIA 2.1, JEIDA 4.2 compliant. 3.3V, 5.0V, or mixed 3.3V/5.0V operation.
◎ Intel 82365SL register compatible, ExCA compatible.
◎ The 3.5" front Drive Unit with built-in one socket is connected to the PCI Interface Board by using the flat ribbon cable.
◎ There are one PC card socket that can be used for Type I / Type II / Type III PC Card in this unit.
◎ Support IRQ steering (PCMCIA -16Bit), native driver built in Windows XP.
◎ Support IRQ steering (PCMCIA -16Bit), optional driver provided in Windows 98/Me, or Windows 2000
Supports PC Cards(TypeI/II/II)
PCMCIA: 8/16 Bit, 8 MHz, 3.3/5V.
CardBus: 32 Bit, 33 MHz, 3.3 V.
Power Voltage@PCI DC 3.3V/5V/12V
PC Card Socket DC 3.3 V/5V @1A
Physical Character @ PC Card Drive
Data Transfer Rate(Max)
CardBus Mode: 132 Mbytes/sec
Operating: 0ºC to 70ºC
Storage: -55ºC to 125ºC
Operating R.H.% 0-70%
Storage R.H. % 0-95%
PCI to PCMCIA/CardBus Interface
Re Trouble shooting
If your computer has Elan PCI card reader before, please remove Elan driver and make sure that your computer has the following file
Our readers use Windows Native driver,
PCMCIA card Drivers Information
Drivers are automatically installed by the Windows when it recognizes a PC Card slot at installation, but often not installed if it doesn't. Typically these drivers are not present on a desktop system since most customers add a PCI to PC Card drive reader well after Windows software is installed on a system.
If you have a retail CD-ROM of the Windows XP/Vista/7/8/10 installation disk, then this isn't an issue since simply inserting the CD-ROM during the new hardware found routine will allow Windows to find and install the correct drivers. However, many end users purchase computers from large vendors with Windows XP/Vista pre-installed and the CD-ROM they get with their system isn't a full copy of Windows (a restore disk) although they paid in full for Windows. In this case the end users needs to contact their system vendor and tell them that they need the "signed Microsoft Windows XP/Vista/7/8/10 drivers for the R5C485, R5C486, R5C843, or PCI1510" depending on which controller their PC Card drive reader uses. The drivers may already be on a system in "C:\\WINDOWS\system32\DRIVERS\pcmcia.sys", and instructing the installation routine to that file may help.